My build (very slowly progressing)
-
I am less familiar with the MYSTAT hardware/firmware, that repository is a fork and you can see the original developers efforts much before mine! Just to say I'm not super familiar, @danielfp248 programed mine and sent it to me in the mail
Yes, the main PSU needs to be connected for current measurents to function.
Also a warning, make sure the MYSTAT is completely powered off and unplugged before inserting/removing the measurement cable to the MYSTAT, otherwise there is a risk of damage.
Are you following the calibration procedure from the original paper with a (IIRC) 1k resistor?
Also actually @danielfp248 made all the code improvements to the repository for MYSTAT, he just dislikes Git and so I'm the one who uploads them
-
Also actually @danielfp248 made all the code improvements to the repository for MYSTAT, he just dislikes Git and so I'm the one who uploads them
-
@czahl ah I think @danielfp248 would know this answer, he has flashed most of the firmware but I don't remember him saying he made any changes. He is traveling right now so it may take him a bit to get back to us. I have only used the MYSTAT, I haven't dealt with the firmware myself. If he made any changes then we can push them to the repo ASAP.
-
@czahl We have never updated the firmware, we use the same one as the original mystat paper. Errors when saving calibration are often related with the calibration parameters being of the incorrect numerical type or the values being too large. There might be a bug in the UI around this. I'll check when I'm back from my traveling, however I dont remember having issues saving these values when calibrating successfully with the 1k ohm resistors.
-
@czahl We have never updated the firmware, we use the same one as the original mystat paper. Errors when saving calibration are often related with the calibration parameters being of the incorrect numerical type or the values being too large. There might be a bug in the UI around this. I'll check when I'm back from my traveling, however I dont remember having issues saving these values when calibrating successfully with the 1k ohm resistors.
@danielfp248 said in My build (very slowly progressing):
We have never updated the firmware, we use the same one as the original mystat paper
Are we talking about the same mystat repo? Again in my understanding this paper reflects the PCB from PcbWay, und this has the 4 reed relais (on top of the picture) for the 4 current ranges. In the main.c only the original 3 are handled.
Somewhere there is a mismatch, or am I'm looking into the wrong repo?
-
@danielfp248 said in My build (very slowly progressing):
We have never updated the firmware, we use the same one as the original mystat paper
Are we talking about the same mystat repo? Again in my understanding this paper reflects the PCB from PcbWay, und this has the 4 reed relais (on top of the picture) for the 4 current ranges. In the main.c only the original 3 are handled.
Somewhere there is a mismatch, or am I'm looking into the wrong repo?
@czahl I dont know which files kirk used to create that repo. I use the firmware directly from the repo linked on the mystat paper.
-
@czahl I dont know which files kirk used to create that repo. I use the firmware directly from the repo linked on the mystat paper.
@danielfp248 Thanks for the hint this is the reason. In the version referenced in the paper, the firmware is extended to support the 4 current ranges.
-
@czahl We have never updated the firmware, we use the same one as the original mystat paper. Errors when saving calibration are often related with the calibration parameters being of the incorrect numerical type or the values being too large. There might be a bug in the UI around this. I'll check when I'm back from my traveling, however I dont remember having issues saving these values when calibrating successfully with the 1k ohm resistors.
@danielfp248 said in My build (very slowly progressing):
however I dont remember having issues saving these values when calibrating successfully with the 1k ohm resistors.
I need to actually do the real calibration when I find the time. I'l report back then.
-
@danielfp248 I managed to get the mystat working correctly and calibrate it too. The problem was the firmware. I was using the one from @kirk's repo but that's the one working for only 3 current ranges. https://github.com/matthew-yates/MYSTAT/blob/main/firmware/firmware.hex is the correct one to use with the updated board. Should I create a pull request?
-
@danielfp248 I managed to get the mystat working correctly and calibrate it too. The problem was the firmware. I was using the one from @kirk's repo but that's the one working for only 3 current ranges. https://github.com/matthew-yates/MYSTAT/blob/main/firmware/firmware.hex is the correct one to use with the updated board. Should I create a pull request?
@sepi yes, please do.
