New member introduction thread!

[HydrogenDream]

Hi, I am Tobi from south Germany. I have found out about the community by searching Google for information about redox flow batteries.
I need a big capacity energy storage for my current project, an electric self sustaining yacht.
The safety of Flow batteries makes them a very attractive choice to me although I do not know yet if energy density and output might fit my needs. But all of my questions for sure will be answered here

If you are keen to see the project, you are welcome to visit me at x.com/dreamhydrogen

[danielfp248]

@HydrogenDream Thanks for joining! Flow batteries have quite low energy density relative to other technologies, so I don't believe they are a right fit for a boat. For this the best practical solution is most likely going to be lithium iron phosphate batteries. These are quite safe and their energy density is a much better fit, especially given the limited space available on a boat.

[sepi]

Also sloshing of large amounts lf liquids might be a problem, both fir stability but maybe also for the battery itself. I guess it all depends on your goals. It it needs to be practical and working tomorrow, LiFePo is probably the way to go. If you have other goals, maybe look further into flow batteries.

[czahl]

Hi, Christian here form Germany, Lower Saxony. I'm a senior software developer and like to play around with electronics, MCUs, ESPs, FreeCAD, 3D printing, milling, and anything else what you can DIY. I'm looking for some ideas to pimp up the energy storage capabilities of my PV setup since 1yr. There are so many ideas including compressed air storage, flywheels, thermal storage, and of course batteries / fuel cells. So I'm reading and viewing tons of research papers and DIY videos regarding this. As some others here, I found the reference to this project on heise.de.

I plan to start with the 3D printing soon. Thanks a lot for all the updates of all of your progress on building the kit. Once I'm ready to start I will also share my experiences during the build and hopefully test process.

[sepi]

@czahl Hello Christian, are you my clone? I could have writtent that message except for the location and Name :D. Anyways, I whish you a warm welcome, fun an patience building your kit!

[danielfp248]

@czahl Welcome to the community Christian! We look forward to your fabrication journey. Please feel free to open up a thread to share your progress with us, that way it will be easier for you to ask questions as you advance and build a successful kit.

[czahl]

@sepi thanks for the warm welcome and hope you are running well with your build - which is already looking very good

[czahl]

@danielfp248 Thanks, I will follow your recommendation. I will open a new thread for this - but first I need to find some extra time to get started . One first step (done today) is to order some PP filament for my Bamboo and to learn who to print it. Once started I will document my experience in the same thread then...

[muntasirms]

Hi all, I'm Muntasir, a doctoral student in chemical engineering at Worcester Polytechnic Institute in Massachusetts the USA. I just started perusing your work - I found it on an Autodesk Research lecture you guys did.

I'm a doctoral student in chemical engineering focusing specifically on scaleup and electrode design of flow batteries (the general idea is - if you start from absolutely nothing, can we get a general idea of electrode properties, dimensions, etc. that would lead to specific power/capacity/cost benchmarks, agnostic to chemistry?) Most of my expertise is tying very parsimonious models to practical performance metrics/experimental data, specifically for all-iron and iron-air chemistries. I'm happy to lend some of my experience (if not at least point folks toward useful resources)!

[kirk]

A belated welcome @HydrogenDream, @czahl, and @muntasirms !

@muntasirms said in New member introduction thread!:

I just started perusing your work - I found it on an Autodesk Research lecture you guys did.

Ah great, I'm glad somebody watched that . For the curious, the talk is here: https://www.youtube.com/watch?v=iIDwj2noVrI

@muntasirms said in New member introduction thread!:

I'm happy to lend some of my experience (if not at least point folks toward useful resources)!

We could definitely use your expertise! I'm also curious to hear your thoughts on the practicality/feasibility of some of the all-iron/iron-air approaches. We'd like to start some more modeling efforts once we're able to run tests in the large-format cell.